What should I set my cutting torch on

The recommended setting is for the fuel gas regulator to be set at 10 psig and the oxygen regulator at 45 psig. This recommendation applies when cutting less than 1.5 inch steel with the use of propane, propylene or natural gas.

What should cutting torches be set at?

Set your acetylene to between 5-7 psi (pounds per square inch). Set your oxygen to 40-50 psi. Turn your oxygen valve on all the way, then turn your acetylene valve a 1/6-1/5 of a turn. Using your striker light the torch facing away from you and the bottles.

What should my oxygen and acetylene be set at for cutting?

The recommended setting for multi-hole cutting is the oxygen regulator at 40 psig with the acetylene regulator setting at 10 psig.

What is the best way to set the oxygen pressure for cutting?

What is the best way to set the oxygen pressure for cutting? Make sure the oxygen cylinder is secure and open the valve all the way. What metals can be cut with the oxyfuel gas process?

Do you turn off the oxygen or acetylene first?

We recommend closing the oxygen valve first whenever turning off an oxy-fuel torch system especially when Acetylene is fuel.

What is the normal working pressure for acetylene?

The working pressure of acetylene equipment is critical: Acetylene pressure must not exceed 0.62 bar (9psi) unless equipment has been specifically designed for it.

What is the ratio of oxygen to acetylene?

Table : Fuel Gas CharacteristicsFuel GasMaximum Flame Temperature °COxygen to fuel gas Ratio (vol)Acetylene3,1601.2:1Propane2,8284.3:1MAPP2,9763.3:1

What gauge pressure should acetylene never be set above?

Never use acetylene at pressures above 15 psi. Using acetylene at pressures in excess of 15 psi gauge pressure (or about 30 psi absolute pressure) is a hazardous practice.

What happens to acetylene above 15 psi?

Acetylene will not explode under low pressure at normal temperatures. However, it becomes unstable and spontaneously combustible when compressed to a pressure over 15 psi. Beyond 29.4 psi, it becomes self explosive, and a slight shock may cause it to explode even in the absence of air or oxygen.

How do you adjust the pre heat flame correctly?

The quantity of preheat can be adjusted by raising or lowering the preheat pressures to the torch. High pressure will result in high flowrates, i.e. a high velocity preheat. Low pressures will result in low flowrates/velocity. The operator can adjust the O/F ratio by looking at the inner cone of the flame.

Article first time published on

What is the number for acetylene?

NamesPreferred IUPAC name AcetyleneSystematic IUPAC name EthyneIdentifiersCAS Number74-86-2

What pressure should oxygen and acetylene be set at for brazing?

Oxygen and acetylene should be set at equal delivery amounts depending on the size and mass of the object being brazed. This would translate into 5 psi oxygen and 5 psi acetylene. These pressures are delivery pressures that must be set as the gas is flowing from the torch tip.

How do you set an oxy acetylene cutting torch?

Turn the acetylene knob on the cutting torch about a quarter of a turn and light the acetylene. Make sure that the flame is up against the tip. If you light up the tip and the flame is away from the tip, decrease the acetylene pressure and let the flame come back against the tip. (Use your safety equipment.)

Do you use more oxygen or acetylene?

For maximum flame temperature in oxygen, the ratio volume of oxygen to fuel gas are 1.2 to 1 for acetylene and 4.3 to 1 for propane. So, there is far more oxygen being consumed when using propane than acetylene. Despite propane being less expensive than acetylene, this is counteracted by the higher oxygen consumption.

How do you set up an oxygen and acetylene tank?

1. Make sure regulator pressure adjustment screws are backed out!
2. Make sure torch valves are closed!
3. Stand away from front of regulator.
4. Separately and slowly open the oxygen and acetylene cylinder valves.
5. Adjust regulator p/a screws to tip pressure settings.

What is the ratio of oxygen to acetylene in carburizing flame?

Carburizing Flame : It has more of acetylene content than that of oxygen, approximately 3:1.

What is the ratio of oxygen to acetylene in a neutral flame for brazing?

A neutral flame uses close to a 1.1:1 ratio of oxygen to acetylene.

What temperature does oxygen and acetylene burn at?

Acetylene when combined with oxygen burns at 3200 °C to 3500 °C (5800 °F to 6300 °F), highest among commonly used gaseous fuels.

How far do you open the valve on the acetylene cylinder?

An acetylene cylinder valve shall not be opened more than one and one-half turns of the spindle, and preferably no more than three-fourths of a turn.

What is the normal working pressure for oxygen?

For many reasons, patients that require additional oxygen use storage tanks with compressed oxygen to supplement their normal air intake. The size and subsequent capacity of the tank may vary but the full pressure is typically about 2,000 psi and can go as high as 3,000 psi.

How much pressure is in a full oxygen cylinder?

A full cylinder will read about 2000 psi (pounds per square inch). the gauge reaches the flow rate your doctor prescribed. the regulator. Secure oxygen cylinders in your vehicle so they do not roll or bump against other cylinders or objects.

Is it safe to lay an acetylene bottle on its side?

Do not lay acetylene cylinders on their sides. If an acetylene tank has accidentally been left on its side, set it upright for at least one hour before it is used.

What will happen if you place an acetylene cylinder on its side?

Acetylene cylinders must not be placed on their sides, since the acetone and binders will have dislodged. The result may be formation of an acetylene “pocket” that is subject to polymerization and the possibility that liquid acetone will be released into the regulator.

Why is the acetylene cylinder valve wrench always left on the valve?

Why should the acetylene cylinder valve wrench be left in position? To close the valve promptly if the need arise.

What is the ideal flame type for oxy cutting?

If the correct size of nozzle is being used a Neutral flame should produce no more than a gentle hiss. A Neutral Oxy Acetylene Flame is used for Welding, Brazing and Silver Soldering most metals and is therefore the most common type of flame to use. A Neutral Flame is also used for Oxy Acetylene Cutting.

What pressure does acetylene become explosive?

Acetylene can also be explosive if the regulated pressure exceeds 15 psi (Pounds per Square Inch). Mixing acetylene with air, liquefying, compressing or heating the gas can also cause potential hazards.

When welding or cutting the acetylene pressure gauge should never be set higher than?

The acetylene pressure gauge should never be set higher than 15 psi for welding or cutting.

When cutting the preheat flame should be?

With the correct nozzle clearance, the preheat flames should not be more than 1/4” above the top surface of the plate. When the nozzle is too low, part of the preheat flame’s inner cones become buried in the cutting kerf. This produces grooves in the cut face and excessive melting of the top edge.

Which flame is suitable for preheating in cutting process?

you have to use an oxidizing flame so we deposited a large amount of oxygen molecules in our walls that will be harmful bisieles our welding the difficult control of the hydrogen generating mainly pore defects.

Why is a cutting torch held at a low angle when thin metal is cut?

This lowered angle effectively increases the thickness of the metal being cut. On very thin metal, holding the tip near vertical produces too much preheating.

Can you use propane for cutting torch?

The gases you can use with oxygen in cutting torches includes acetylene, propane and others. … Acetylene burns much hotter than propane and therefore can cut quicker; but propane is usually cheaper than acetylene and can be used just as effectively in a cutting torch.