What is Rumber flooring

Rumber floorboards first appeared in horse trailers in 1992. Made with 100% recycled tires, they were designed as a replacement for cumbersome aluminum and wood floors covered with rubber matting. The 1 ½” x 7” tongue-and-groove boards are installed running front-to-back in a trailer.

How much does Rumber flooring cost?

Depending on trailer length and the number of boards, easy-to-install, low-cost kits range from $750 to $22,500 per trailer. Visit rumber.com or call 1-877-786-2371 for more information.

What is a Rumbar floor?

Rumber is a synthetic material made from old recycled tire bits. Tongue-and-groove boards are fitted together to form a solid surface without the need for rubber mats on top. To clean this floor, you can simply hose it out and let it dry.

What is a horse trailer floor made of?

Traditionally horse trailer floors were made from hardwood timber planks usually Keruing, this is a brilliant material and with a high resin content was virtually rot proof.

What kind of wood is used for horse trailer floors?

For replacement boards, well-cured oak or pine are the best. Pressure-treated wood is ok, but it will eventually rot also if the floors are not maintained. Be sure to leave a “pencil” space between the boards, so urine can drain out and air can dry the boards.

How do I know if my horse trailer floor is good?

15 Minutes – Flooring Use a screwdriver or a dull knife to check the integrity of the trailer floor: If the tip of the tool sinks into any of the floor’s wooden boards, they need to be replaced. Be especially thorough around the edge of the floor, where rot is most likely to begin.

Can you use composite decking for trailer?

A few downsides are weight and the potential for staining (although I’m not really concerned about staining). The trailer will have 12″ spacing on cross members so it will be supported consistent with manufacturer specs for composite decking.

What is a Rumber floor in horse trailer?

Rumber floorboards first appeared in horse trailers in 1992. Made with 100% recycled tires, they were designed as a replacement for cumbersome aluminum and wood floors covered with rubber matting. … They’re supported underneath with floor supports, running side-to-side, approximately 10 to 15 inches apart.

How much does it cost to replace horse trailer floor?

If you ever have to replace or repair the floor the lumber is readily accessible, cheap, and it doesn’t require an expert to install. The typical range is from $600-900 depending on the size of your trailer and if you have a dressing room.

What is the best wood to use for a trailer floor?

Pressure treated Pine flooring is the most commonly used wood flooring material in trailers. The abundant supply of Pine wood in the south coupled with its sturdy nature make for a solid basic flooring choice.

Article first time published on

What kind of wood is used for flatbed trailers?

Treated Pine? The answer is Apitong also known as Keruing. Apitong / Keruing is used by all major flatbed trailer manufactures like Great Dane, Fontaine, Wilson, Transcraft, MAC, Wabash, Doonan Specialized Trailer, XL-Specialized and more.

What is a composite trailer?

As their name suggests, composite trailers are composed of composite material, with smooth interior walls. This design reduces the chances of snagging or damaging the freight on the insides of the trailer during loading and unloading.

What do you use for floating floor for horses?

Aluminium: Aluminium is a fairly recent flooring option as it offers the promise of no rust or rot due to moisture and on the surface seems to be a good choice. Unfortunately, it also suffers from deficits and while less dramatic than timber, they represent safety and comfort issues for your horse.

How do you fix rust on a horse trailer?

Scrub the rusted areas with sand paper and steel wool. These are effective tools in removing rust in easy-to-reach spots, but they do no work well for small crevices. Pour table lemon juice onto the rusted area. Then pour salt over the lemon juice.

Do horse trailers need mats?

As you can see above, some of the horse trailer floor types require rubber mats and other do not. … Treated lumber and aluminum floors do require rubber mats so that the horse’s hooves do not directly damage the floor material. These mats also provide extra “grip” for their feet and protect the floor from moisture.

Why do people put shavings in horse trailers?

One of the main reasons for this is to cut down on the amount of dust in the trailer. Simple. Many horses are sensitive to dust, and when you have some fine shavings or sawdust in the trailer, dust may be stirred up more than you would like.

Do horse trailers have wood floors?

Wood floors provide a cooler horse trailer. The inside of a horse trailer can start to feel very hot in the Summer sun. … Wood has less heat transfer from the hot road surface than aluminum making the inside of the trailer cooler than one with an aluminum floor.

How thick should a trailer floor be?

The popular thickness would be 3/4″ of some kind of wood. If you do have that, then we recommend going with 0.045″ or 0.063″ (1/16″). The more structure and support you have on the bottom, the thinner you can go. 0.045″ would be the thinnest we recommend.

Is Pine good for trailer decking?

Southern yellow pine (SYP) may be the most frequently used wood trailer decking material. … SYP is used for trailer decking for two main reasons: its strength and its ability to absorb treatment. Even though it is not considered a hardwood, pine is a very strong fiber.

Is Cedar good for trailer decking?

Description: Western Red Cedar is popular for decking, siding and paneling applications. It is not a good industrial wood despite its natural durability. It is too soft for any reasonable application in the truck and trailer industry.

How do you put paneling on a horse trailer?

Install the paneling starting with the back right side of the trailer. Apply construction adhesive to the insulating panels, and drill 1/8-inch holes through the paneling and into the metal wall supports from the top of the trailer to the floor. Drive screws into the holes to tightly secure the paneling into place.

How do you insulate a horse trailer dressing room?

If you really want it Insulated, fill the vertical spaces then put wood strips horizonally and insulate between them, cut it tight enough and cover it with something and you won’t need to glue or screw it.

Is Red oak good for trailer decking?

It is suitable for building boats and outdoor furniture while red oak wood should be used only for cabinets and indoor furniture. Due to its durability, white oak is slightly costlier than red oak. Oak wood is an appropriate choice for building truck trailer decking.

What is plate trailer?

A plate trailer typically (but not always) has the structural posts showing on the outside and the actual trailer walls are very thin. So they are usually quoted in the trailer company’s spec at 100.5 or 101 inches wide inside.

What is a composite van?

“For me the definition of a composite caravan or RV is a build that’s been made up of composite sandwich panels; where the floor, wall and roof panels consist of an internal and external face sheet and a core which has been laminated together,” he said.

How much does a utility dry van trailer weigh?

An empty 53-foot dry van trailer will weigh anywhere from 33,000 to 36,000 pounds, leaving you with 44,000 to 47,000 pounds to operate with. That said, you can’t take 47,000 pounds and plop it directly onto the rear axles of the trailer.