What does e90 mean on Intex hot tub

If alarm code E90 is displayed on the control panel, it means no water is flowing through the system. Check the attached troubleshooting guide.

How do I fix my E90 code on my Intex hot tub?

If the E90 code appears after running for a while: Check and ensure there is no debris inside the spa tub inlet and outlet grids. If there is debris inside, turn the control unit off, unscrew the spa inlet/outlet grid with a Phillip screwdriver. Clean and replace it back. Make sure the spa water is clean and sanitized.

How do you reset an Intex hot tub?

Be sure to press the “Reset” button on the spa control unit side using a small and thin object before the first time operation.

What is E90 error?

As for the E90 fault. It indicates no water flow. They shut down for two reasons. Without flow the heater could over heat and cause a fire.

What does E95 mean on a Intex hot tub?

If alarm code E95 is shown, it means the water temperature is too high. Let the spa water cool down to 104ºF (40ºC) or below, reset the control panel information by unplug and plug back in the GFCI/RCD, and reset the GFCI/RCD to restart the system.

How long does it take for an Intex spa to heat up?

I turned on the heater and in about 24 hours the temperature was up to 103, and this was with ambient outdoor air temperature of 35-40 degrees.

How do you fix the error code on a hot tub?

Shut down the spa at the breaker.
Make sure there is no debris in the water that can get sucked into the pump.
Take out all of the filter(s) and set them aside.
Turn spa back on at the breaker with the filters out.

What does e2 mean on hot tub?

The E02 error code can occur when the filters are dirty or blocked. SOLUTIONS WASH OR CHANGE THE FILTERS. Remove the filter cartridge from the filter housing. Using luke warm water, run the filter cartridge under the water until it runs clear.

Why does my Intex Spa say end?

If alarm code “END” is displayed on the control panel, it means that the actual water temperature could not rise to the set temperature after 72 hours of continuous heating causing the rapid heating and water filtration functions to be temporarily disabled.

What does se mean on a hot tub?

CODEERROR CODE DESCRIPTIONSESpa in standard-in-economy mode; system message, not an errorSEoPSensor open or disconnected; heater disabled but spa operationalSESHSensor short, nonfunctional; heater disabled but spa operationalSHShort circuit on temperature sensor

Article first time published on

What does Fl mean on a hot tub display?

Today’s post is about water flow trouble codes on your spa panel. These are usually presented as FL, FLO or FLOW on your display, although it may appear as LF (Low Flow) or PS (Pressure Switch). Low flow error codes are really a self-preservation exercise for your hot tub.

Will an airlock clear itself?

Airlocks do sometimes fix themselves, but it isn’t a risk worth taking. Airlocks occur when air becomes trapped in the hot water or central heating system. Vapour becomes caught in a high point of the pipework because the gas is less dense than the water in the system.

How do you know if you have an air lock in your hot tub?

As mentioned above, the most common sign that your hot tub has an air lock is the jets not working when powered on. This can include nothing coming out of your jets when they are turned on or even a humming sound coming from the jets or pump.

Why is my hot tub buzzing?

The most common problem that could occur when a hot tub hums is an air lock in the hot tub. … Air pockets prevent hot tub pump from pushing the water properly and eventually, it could lead to the pump to break. These air pockets or air lock need to be purged before your pump can work again.

What temperature should you keep your hot tub when not in use?

While it may sound like common sense to turn your hot tub down every time it is not in use, it’s actually better to maintain a constant soaking temperature, which is typically around 100° Fahrenheit for many people.

How long should a spa pump run per day?

Since your hot tub pump circulates the warm water as well as the sanitizer, a general rule is to follow manufacturer recommendations or leave the pump on for a minimum of eight hours per day.

How long do inflatable hot tubs last?

When considering the lifespan of your new hot tub, you can expect to receive around 5 -7 years of use out of an inflatable hot tub compared to 20+ years of use from a hardshell hot tub.

Should Jets be on when heating hot tub?

Before covering your hot tub, make sure to turn on the jets as this will accelerate the pace of your hot tub’s heating. By running the jets, you’re allowing the heated water to be circulated and evenly distributed to all areas of the hot tub.

How long does it take to heat up a 110v hot tub?

Usually, a 110v hot tub will heat by one to two degrees per hour. Depending on the hot tub water’s starting temperature, it can take anywhere from a couple of hours to over a day to reach ideal temperatures. Hot tubs are great for relaxation and warming up when it is cold outside.

How often should you change the water in an inflatable hot tub?

The Lay Z Spa Paris holds 250 gallons of water. Divide that by 3, and you get 84 (rounded up from 83.33). If 2 people use the hot tub regularly every day, then 84 divided by 2 equals 42. This means you need to change the water every 42 days, which is once every 6 weeks.

Why is my inflatable hot tub slimy?

What causes hot tub slime? Slime can be caused by a build-up of bacteria and microorganisms, known as biofilm. This can sometimes be seen and felt on your hot tub interior or can build up undetected in plumbing. If you are suffering from cloudy water or water odour, you may have slime in your pipes.

Should I leave my hot tub on all the time?

One question we sometimes get asked is should I leave my hot tub on all the time? The answer is yes! Hot tubs are designed to be left on permanently and this is how they work best. Of course, they’ll need to be drained regularly but for the most part, they are left on 24/7.

Why does my hot tub switch itself off?

First, check your water level. Then, look for clogs in your circulation system, and wash or change your filter. … If the high limit switch shut your heater off because your water got too hot or you have air trapped in your lines, resetting the heater will get it going again.

Can I turn my Lay Z Spa off?

Can I leave the spa on all the time? The spa can be left on, if the heater function is left on, the pump unit will maintain the temperature of the water for you. … Please note that if the pump unit is not touched for a period of 72 hours the heater will switch off.

Should I leave my lazy spa on all the time?

Leave Your Lay‑Z‑Spa Heater Activated Between Uses Depending on the amount you use your Lay‑Z‑Spa, in our experience it is better to leave the heater activated all of the time, if used regularly ‑ say 3 or more times per week.

How do I fix error 2 lazy spa?

Run the spa with the heating and filtration system. If the E02 error code disappears for 2 to 3 hours, the issue is caused by the filter housing black membrane being perished or twisted. This filter housing will need to be replaced if this is the case.

How do I fix error code E01 on a lazy spa?

E01. The water flow sensors’ flags didn’t come back into the correct position. Unplug the pump unit, lightly strike the side of it and then plug it back in. If the unit does not respond, try rolling the pump unit on its side in order to shift the sensor placement.