How do I connect my Lutron dimmer

Press and hold the “Off” button on the dimmer/switch you wish to pair the Pico remote to for 6 seconds until the green indicator lights on the unit begin to flash, then release. This will place the device in pairing mode.

How do I pair my Lutron Caseta dimmer switch?

Press and hold the “Off” button on the dimmer/switch you wish to pair the Pico remote to for 6 seconds until the green indicator lights on the unit begin to flash, then release. This will place the device in pairing mode.

How do I connect my Lutron?

Tap on the Lutron Connect app in the search results. Tap on the Install button and then choose to Accept the access request. The Lutron Connect app will then begin to download onto the device. Make sure that the mobile device is connected to the local Wi-Fi network that the Lutron Connect Bridge resides on.

What is the red wire on a Lutron dimmer switch?

Red is the switched lead (or a traveler in a 3-way installation), and is attached to the switched hot going to the light. Red with white is a traveler, used for 3-way installations. In your situation, you’ll just cap this one off. Green is ground, and is attached to the grounding conductor.

How do you reset a Caseta dimmer?

How do I factory reset my Lutron Caseta dimmer? Rapidly tap the top “on” button three times and on the third tap hold until the lights connected to the switch begin to dim up and down, immediately tap the top “on” button three times rapidly. The connected lights will then alternate dim and bright slowly.

Is red wire same as white?

The white wire is always neutral, and when the cable has only two conductors, as most 120-volt cables do, the hot wire is black. … The red wire is for the light switch. This configuration, sometimes called a half-hot or split-tab outlet, is becoming increasingly popular, so it’s good to know how to wire it.

Can I connect red and black wires together?

Red Electrical Wires These wires are typically used for switch wiring as well as the interconnection between smoke detectors hard-wired into the power system. You can link two red wires together, or you can link a red wire to a black wire. Since red wires conduct current, they are considered hot.

Why is my Lutron App not working?

All Users: If you are still unable to connect, we recommend that you reset your router by disconnecting the power for 10 seconds. This will restart the bridge. If the Lutron App is still unable to find the bridge, this is most likely because the Bridge and your smart device are not connected to the same network.

What is the blue wire on Lutron switch?

The ground (green or uncoated) goes to all the grounds and to the switch ground (if there is a ground screw). The blue wire is typically capped (not used) as it likely is used as a “traveler” wire for “3-way” circuits (more than one switch to operate the circuit).

How do I connect my Lutron to a new WIFI?

1. Make sure your Smart Bridge is connected to the new router. …
2. Connect the ethernet cable from the bridge directly to a LAN port on the new router.
3. Re-set your router by cycling power off for 10 seconds and then turn it back on. …
4. Re-set your Smart Bridge by cycling power off for 10 seconds and then turn it back on.

Article first time published on

How do I find my Lutron IP address?

The Lutron App will walk you through the initial system setup and adding devices. The integration report and IP address settings are found in the Settings ->Advanced menu of the app. Tap the icon in upper left corner to access the Settings menu.

How do you reset Lutron homework?

Reset Factory Default performs the same function as a triple-tap, hold, triple-tap (see page 6). To access the Maintenance screen, hold the ON and OFF buttons down simultaneously for 10 seconds, then release. Restoring the Dynamic Keypad to factory settings will remove it from the system and will clear its programming.

How do I reset my Lutron WIFI?

Re-set your router by cycling power off for 10 seconds and then turn it back on. Wait until the router completes the re-start process (up to 5 min depending on your router) Re-set your Smart Bridge by cycling power off for 10 seconds and then turn it back on. This will re-start the smart bridge.

What happens if you switch Red and black wires?

If you switched the wires, what would happen? Red is positive charge, black is negative charge. If you aren’t running if you aren’t connected correctly.

Does Red wire go to white?

Sheathed cable with a red wire always is accompanied by a black wire, a white wire and a bare wire. Very old homes may have cable that excludes the bare wire.

What cords have Red and black wires?

The red wire is a positive power wire with 5 volts of DC power. The black wire is the ground wire (similar to most all electronic devices).

What color wire does Red connect to?

Red: Hot Wire Like black electrical wires, red wires are also hot or live wires. Red can also be the connecting wire between two smoke detectors that are hardwired. Also, if your circuit box is wired for 240 volts instead of 120 volts, you may even see both red and black wires.

Where does the red wire go on an outlet?

The red wire (switched hot wire) going to the outlet, wires into the other side of the switch and the white wires (neutral), tie together to complete the return side of the circuit. One of the most common wiring configurations your going to find with outlets are shown in the diagram below.

What is a red wire used for?

What are Red Wires? Red wires are usually used as secondary hot wires. Red wires are also hot and should be clearly marked to avoid the dangers of electrocution. Red wires are commonly used when installing ceiling fans, where the light switch maybe.

Does red wire connect to blue?

In your case the red wire should be connected to the hot (black) wire from the junction box, and blue should be connected to the neutral (white) wire from the box. If there is a green, green and yellow, or just bare copper wire, that’s the ground wire.

Can you put black and blue wires together?

If you only have one switch, connect the black and blue wires. The black and blue wires need to be connected. You will be able to control your fan and lights with a single switch.

Why are both wires black?

The United States has strict codes relating to home wiring, including clearly defined colors on the outer casing of the wires. Black means hot, white signifies neutral, and green indicates ground. However, if you need to rewire a light switch or a plug socket, you may occasionally come across two black wires.

How do I install a Lutron hub?

This is pretty easy. Just take the included power and ethernet cables and connect them to the hub. After that, plug the power into a free outlet and the ethernet into an open ethernet port on your router. From there, lights will begin to blink on the hub to let you know it’s ready for use.

How do I reset my Lutron Connect bridge?

Step 1: Quickly triple tap and hold any button on the keypad. DO NOT release after third tap. Step 2: Keep the button pressed after the third tap for a few seconds until all the status LEDs start to flash slowly (approximately once per second). The keypad has now been returned to Factory Default Settings.

How do I reset my Lutron Smart Bridge?

The BLACK button on the back – you can perform the standard 3-press-hold-3-press reset. I have had success with this method after speaking with Lutron regarding a few issues we were having. Procedure: Press the black button on the back of the Smart Bridge Pro 3 times, holding it for 10 seconds on the 3rd press.